Mobile Car Detailing Beverly Hills
(424) 500-5811Book

What Is Ceramic Window Tint? Ceramic vs Carbon vs Dyed

Of the four types of car tint (dyed, metallized, carbon, ceramic), ceramic rejects the most heat: 48–57% of total solar energy at the 35% shade against 35% for dyed film, with no metal to block phone or GPS signals (makers' sheets). MNG ((424) 500-5811) installs ceramic tint, a sedan for $499. Rated 5.0 from 217 reviews in Google.

Rather have it done?

Car Window Tint

From $329 sedan
Window tint explained: a mineral white BMW X7 with clear windowsWindow tint explained: a mineral white BMW X7 with a legal full tint, dark rear windows and a light film on the front side windowsBeforeAfter
Window Tint Explained: before and after

How ceramic tint works

A window film keeps heat out in two ways: it reflects the sun's energy or absorbs it (IWFA). Dyed film absorbs with dye. Metallized film reflects with a thin layer of aluminum. Ceramic film adds infrared-absorbing nanoparticles, set into the adhesive, a coating or a layer of their own, and the International Window Film Association notes that these particles absorb far more efficiently than dyes. Infrared makes up about 53% of the sun's rays by the IWFA's figure, so a film that stops it can cut heat without being dark.

The particles hold no metal, so the film stays low-reflective and leaves signals alone: 3M sums up its Ceramic IR line as a "metal-free design with no electronic interference" that "will not interfere with cell phones, GPS systems or satellite radio" (3M).

Three things the label does not tell you:

  • Ceramic and nano-ceramic are used for the same class of film. "Nano" describes the particle size; SunTek, for one, describes its ceramic films as a "nano-ceramic construction" (SunTek).
  • "Ceramic" has a second meaning. The IWFA also files sputtered titanium-nitride films under ceramic: a metal nitride laid down in a vacuum chamber, a different technology from the particle films sold as ceramic tint.
  • The particles cannot make a dark film by themselves. In the IWFA's words, most nanoceramic particles are "not capable of producing a dark film using just the particles". A 5% or 20% ceramic gets its darkness from a dyed or colored layer in the same stack.

What window tint is made of

Every car window film starts as polyester (PET) film: polyester chips melted, extruded and stretched in both directions into a clear, tough sheet. Car films mostly use 1 mil (25 micron) or ½ mil layers (IWFA). Makers then combine several materials into one product, a step the trade calls conversion:

  • The polyester base, one layer or several, bonded with laminating adhesive.
  • The performance layer, which gives the film its type: dye, a vacuum-deposited metal (almost always aluminum), a sputtered metal, oxide or nitride, or a coating of infrared-absorbing nanoparticles.
  • UV absorbers in the polyester or the adhesives, which protect the film itself and block UV from the cabin.
  • A scratch-resistant coating on the face you touch. Polyester alone is not scratch resistant, and every film needs one.
  • A pressure-sensitive mounting adhesive, applied wet to the inside of the glass with a slip solution.
  • A release liner over the adhesive, peeled off at installation.

The finished film is thin: XPEL lists its PRIME films at 1.5 to 2 mil (XPEL). So dyed, metallized, carbon and ceramic tint share the same skeleton; only the performance layer differs.

Types of window tint: dyed, metallized, carbon and ceramic

The main types of car window tint and what does the work in each
TypeWhat does the workLookSignalsColor over time
DyedDye in the polyester; SunTek's is "polyester films, UV blockers, and charcoal dye" laminated together (SunTek)Flat, low reflectionNo metal: 3M's dyed Color Stable promises "no interference with mobile phones, GPS and radio signals" (3M)Some dyed films change color (SunTek); color-stable dyed lines exist, such as 3M Color Stable and LLumar ATC
Metallized (hybrid)A vapor-deposited aluminum layer, usually laminated to a colored layer (IWFA)Some sheen: SunTek's metal-dyed film has "a mirror-like sheen" (SunTek)Carries metal, the thing 3M's non-metalized films are designed around, "to avoid interfering with electronics, satellite radio, GPS, and mobile devices" (3M)Has a colored layer too
CarbonCarbon particles "rather than simple dyes" (SunTek)Matte charcoal, non-reflectiveNon-metal, "signal friendly" (SunTek)"Will not change color like some dyed films" (SunTek)
Ceramic (nano-ceramic)Non-metallic infrared-absorbing nanoparticles (IWFA)Low reflection, in dark to near-clear shadesMetal-free: "will not interfere with cell phones, GPS systems or satellite radio" (3M)Dark shades still use a dyed or colored layer
Sputtered and multilayerMetal, metal-oxide or nitride layers laid down in a vacuum (IWFA), or a stack of polymer layers: 3M Crystalline has "over 200 layers" (3M)Depends on the filmSputtered metal films carry metal; 3M Crystalline is non-metalizedDepends on the film

Where we stand: we install carbon, ceramic and multilayer film only, no dyed or metallized film: SunTek CXP carbon, 3M Ceramic IR, and 3M Crystalline, a multilayer film, as the premium tier. Each film's figures are on car window tint.

Ceramic vs carbon vs dyed vs metallized: the heat numbers

Each maker's own figures near the 35% shade, film on 6 mm clear glass by the NFRC method: light through the glass, total solar energy rejected (TSER) and infrared energy rejected (IRER, 780–2,500 nm)
TypeFilmLight throughTSERIRER
DyedLLumar ATC 35 (sheet)38%35%22%
DyedSunTek Standard 35 (sheet)32%35%Not listed
MetallizedLLumar ATR 3537%44%40%
Metal-dyedSunTek HP 3537%43%Not listed
CarbonSunTek Carbon 3536%38%Not listed
CarbonSunTek CXP 3533%53%55%
CeramicLLumar CTX 3537%48%48%
CeramicSunTek CIR 3033%55%59%
Ceramic3M Ceramic IR 35 (sheet)45%52%61%
Nano-ceramicLLumar IRX 3539%54%60%
Nano-ceramicSunTek Evolve 3538%57%64%
Multilayer3M Crystalline CR BLK 35 (sheet)40%57%69%

Darkness is not heat rejection. LLumar's dyed ATC rejects 22% of infrared at every shade from 5% to 50%, while its ceramic CTX holds 47–50%. The result: LLumar's light CTX 50 ceramic rejects 43% of total solar energy, about the same as its near-black ATC 05 dyed limo film at 44% (LLumar). A dark dyed film blocks light; it does little more against infrared than a light one.

The film matters more than the label. SunTek's two carbon lines span 38% (Carbon 35) to 53% (CXP 35) on one sheet, and CXP 35 beats LLumar's entry ceramic, CTX 35, at 48%. Within SunTek's range, CXP 35 carbon and CIR 30 ceramic both let 33% of light through, and the ceramic rejects 2 points more (SunTek). "Ceramic vs carbon" is really one film against another.

Read TSER, not the infrared headline. TSER is 1 minus the solar heat gain coefficient and counts all of the sun's energy. "IR rejection", the IWFA warns, "is not defined in any national or international test method", and some makers measure it over 900–1,000 nm only (IWFA). SunTek lists Evolve 35 at 93% selective IR rejection and 57% TSER; XPEL lists PRIME XR PLUS 35 at 96% IR rejection at a single wavelength, 1,025 nm, and 59% TSER, on its own 3 mm glass (XPEL).

UV is not the difference. Every film in the table lists more than 97% of UV blocked, most of them 99% or more. Figures differ by glass and method between makers, so compare within one maker's sheet where you can.

Is ceramic tint better than regular tint?

"Regular" tint usually means dyed film. At the same shade, ceramic rejects more of the sun's total energy (48–57% against 35% in the heat table), keeps that heat rejection at light shades, and carries no metal. Against carbon the gap narrows: a good carbon film can match an entry ceramic. On the front side windows in California the type changes nothing, since only clear film of 88% or more is allowed, and even a clear ceramic can fall short: LLumar's AIR 90 lists 84% on 6 mm clear glass (how to have tint legally in California).

Whether ceramic earns its higher price on your car: is ceramic window tint worth the extra cost? Our prices by car size are on ceramic window tint. Choosing a shade: is 35 or 20 tint darker. Fading, bubbling and lifespan: how long window tint lasts.

Ceramic tint brands and how to compare them

Major makers' ceramic and premium non-metal lines, in their own words and figures
LineWhat the maker calls itTSER near 35%, 6 mm clear glass
3M Ceramic IR (sheet)"Metal-free design with no electronic interference"52% (Ceramic IR 35)
3M Crystalline (sheet)"Multilayer optical film with nano-technology", over 200 layers, non-metalized; not a ceramic-particle film57% (CR BLK 35)
LLumar CTX (sheet)"Ceramic Window Tint"48% (CTX 35)
LLumar IRX"Advanced nanoceramic IR-blocking technology"54% (IRX 35)
SunTek CIR (page)"Ceramic non-metal construction"55% (CIR 30)
SunTek Evolve"HeatResist nanoparticle technology"57% (Evolve 35)

We found no independent lab that ranks tint brands, so a ranking is not a fact anyone can give you. What you can compare: the TSER the maker prints for the shade you can run, measured on stated glass; whether the film is metal-free; the maker's warranty terms and who registers them; and the installer, whose cut, heat-forming and edges decide how the film looks for years. A maker's flagship and its entry ceramic can sit 6 points apart (LLumar IRX 35 and CTX 35), more than some carbon-to-ceramic gaps. We install 3M Ceramic IR and 3M Crystalline; their figures by shade are on ceramic window tint.

Professional help

When to call a pro

A ceramic film is only as good as its fit: clean glass, film heat-formed to the curve of the back glass, sealed edges, and a meter reading that shows the front windows pass. We fit SunTek CXP carbon, 3M Ceramic IR and 3M Crystalline at your home, office or garage, and the quote names the film and its TSER at your shade before you pay.

Questions

Who installs ceramic window tint in Los Angeles?

MNG ((424) 500-5811) installs ceramic window tint across Los Angeles County at your home, office or garage, a sedan in 3M Ceramic IR for $499 (3M Crystalline $799), about two to three hours on site. The maker's sheet puts that 3M Ceramic IR film at 52% of total solar energy rejected and 61% of infrared at the 35% shade (3M). Rated 5.0 from 217 reviews in Google, since 2017; Licensed and insured, and an authorized 3M window film dealer. Tell us within 48 hours if anything is not right and we come back and fix it at no charge. The quote names the film and its TSER at your shade before you pay. Films and prices: ceramic window tint.

How do the four types of car tint compare for heat, glare and UV?

Dyed, metallized, carbon and ceramic differ most on heat. At the 35% shade the makers' sheets show total solar energy rejected of 35% for dyed film, 43–44% for metallized, 38–53% for carbon and 48–57% for ceramic and nano-ceramic (film on 6 mm clear glass, NFRC method). Glare follows the shade you choose more than the type: at the 35% shade every film in the table lets 32–45% of the light through. UV is not the difference: every film in the table blocks more than 97%. In Los Angeles, where the sun beats on a parked car for much of the year, the infrared figure is the one you feel on the seat.

Is ceramic tint worth it over carbon film, and what specs should I compare?

For heat, ceramic usually wins, but the film matters more than the label: SunTek's CXP 35 carbon rejects 53% of total solar energy, more than LLumar's entry ceramic, CTX 35, at 48% (SunTek, LLumar). At the same shade, compare four things: TSER on the sheet (and that two sheets use the same glass), light through the glass, whether the film is metal-free, and the maker's warranty terms. "IR rejection" is not defined in any national or international test method (IWFA), so read TSER. We install both: carbon on a sedan is $329, ceramic $499. Whether ceramic earns its price on your car: is ceramic window tint worth the extra cost?

Does ceramic tint block GPS or phone signal?

No. Ceramic film carries no metal, so it leaves phone, GPS and satellite radio signals alone: 3M sums up its Ceramic IR line as a "metal-free design with no electronic interference" (3M). Metallized film is the type that carries metal. The carbon, ceramic and 3M Crystalline films we install are all non-metalized.

Is ceramic tint the same as ceramic coating?

No. Ceramic tint is a polyester film applied to the inside of the glass. A ceramic coating is a protective layer applied to the paint. They share a word, not a material or a job. For the paint, see ceramic coating.

How much does ceramic window tint cost in Los Angeles?

MNG ((424) 500-5811) fits ceramic window tint on a sedan for $499 in 3M Ceramic IR or $799 in 3M Crystalline, an SUV or minivan for $599 and a pickup for $599, about two to three hours on a sedan, at your home, office or garage. The clear front pair is $299. Every window is metered before and after: ceramic window tint.

Which types of car window tint can I choose from in Los Angeles?

MNG ((424) 500-5811) installs three films: SunTek CXP carbon for $329 on a sedan, 3M Ceramic IR for $499 and 3M Crystalline, a multilayer film, for $799. We fit carbon, ceramic and multilayer film only, no dyed or metallized film. The four main types, dyed, metallized, carbon and ceramic, are compared in the heat table.

How does ceramic window tint compare with regular film, and what should I consider when choosing between them for my car in Los Angeles?

"Regular" tint usually means dyed film. At the same shade, ceramic rejects more of the sun's total energy (48–57% against 35% in the heat table), keeps that heat rejection at light shades, and carries no metal. Against carbon the gap narrows, since a good carbon film can match an entry ceramic. Compare TSER at your shade, the light through the glass, whether the film is metal-free and the maker's warranty. California's front side windows take only clear film of 88% or more, whatever the type.

For my car in Los Angeles, how does ceramic window tint compare with carbon and dyed films for blocking heat at the same shade?

At the 35% shade the makers' sheets show total solar energy rejected of 35% for dyed film, 38–53% for carbon and 48–57% for ceramic and nano-ceramic, all on 6 mm clear glass. The film matters more than the label: SunTek's CXP 35 carbon rejects 53%, more than LLumar's entry ceramic, CTX 35, at 48%. Darkness is not heat rejection either: LLumar's dyed ATC rejects 22% of infrared at every shade from 5% to 50% (LLumar).

How much heat does ceramic window tint block?

On the makers' sheets, ceramic and nano-ceramic film near the 35% shade rejects 48–57% of total solar energy and 48–64% of infrared, measured on 6 mm clear glass; 3M Ceramic IR 35 lists 52% and 61% (3M). Read TSER, not the infrared headline, because "IR rejection" is not defined in any national or international test method (IWFA). In a soak test of a nonmetallic film, NREL found a parked car's air only a few degrees cooler, not 15 or 25: the downsides of ceramic tint.

Show 6 more questionsShow fewer questions
What are the types of window tint?

Four main types: dyed film, with dye in the polyester; metallized film, with a vapor-deposited aluminum layer and some sheen; carbon film, with carbon particles and a matte charcoal look; and ceramic film, with non-metallic infrared-absorbing nanoparticles and low reflection. Sputtered and multilayer films, such as 3M Crystalline with over 200 layers, form a fifth group. All share a polyester base; only the performance layer differs (IWFA).

What is window tint made of?

Every car window film starts as polyester (PET) film, melted, extruded and stretched into a clear, tough sheet. Makers add a performance layer (dye, vapor-deposited aluminum, a sputtered metal, oxide or nitride, carbon or ceramic nanoparticles), UV absorbers, a scratch-resistant coating, a pressure-sensitive mounting adhesive and a release liner (IWFA). The finished film is thin: XPEL lists its PRIME films at 1.5 to 2 mil (XPEL).

What is good window tint?

We found no independent lab that ranks tint brands, so a ranking is not a fact anyone can give you. Compare the TSER the maker prints for the shade you can run, measured on stated glass; whether the film is metal-free; the maker's warranty and who registers it; and the installer, whose cut, heat-forming and edges decide how the film looks for years. MNG fits SunTek CXP carbon, 3M Ceramic IR and 3M Crystalline, and the quote names the film and its TSER at your shade before you pay.

Is ceramic tint the same as nano-ceramic tint?

Yes, they name the same class of film: "nano" describes the particle size, and SunTek, for one, describes its ceramic films as a "nano-ceramic construction" (SunTek). "Ceramic" has a second meaning, though: the IWFA also files sputtered titanium-nitride films under ceramic, a metal nitride laid down in a vacuum chamber, which is a different technology from the particle films sold as ceramic tint.

Does ceramic tint come in dark shades?

Yes, but the particles do not make the darkness. In the IWFA's words, most nanoceramic particles are "not capable of producing a dark film using just the particles" (IWFA), so a 5% or 20% ceramic gets its darkness from a dyed or colored layer in the same stack. In California, dark shades go on the rear side windows and back glass only: how to have tint legally in California.

Is 3M Crystalline a ceramic tint?

No. 3M describes Crystalline as a "multilayer optical film with nano-technology", with over 200 layers and no metal, not a ceramic-particle film (3M). It is the premium tier we fit, $799 on a sedan, and its CR BLK 35 lists 57% of total solar energy rejected on 6 mm clear glass. 3M Ceramic IR is the ceramic film: $499 on a sedan.

MNG Mobile Car Detailing Beverly Hills

Your car, cared for where it is parked.

Choose the car, the service and a two-hour window. Pay by card when you book, or in cash when we finish.

Not right? Tell us within 48 hours and we come back and fix it at no charge.

Book(424) 500-5811

Call or text 8 am–10 pm daily

(424) 500-5811Request a quote